SubMonitor Starter
SubMonitor Starter
3Ø, 50/60 Hz, 200~600 VAC, 2–300 HP
Equipped with the Franklin Electric SubMonitor Connect overload relay, the SMS provides ideal motor protection for Franklin Electric submersible motors.
-
Electronic Overload Motor Protection
- Wide range, adjustable, class 5-30 electronic overload
- Dry pump detection protects your pump and motor from adverse conditions and allows for time-based automatic restart with well recovery mode
- Industry-leading motor protection for the following conditions:
- Over/under power (dry-run)
- Over/under voltage protection
- Voltage phase loss
- Voltage
- Current phase unbalance
- Locked rotor
- Cycle fault
- Ground Fault
- Easy access to input and output terminals
- 32-character, backlit, NEMA 4x, wash-down rated screen mounted on front of panel allowing for safe viewing of conditions while motor is running
- Motor insulation check
Real-time & Date-stamped Fault Logging
- Unit ships with a pre-programmed real time clock with a 10-year battery backup
- Contains separate fault, configuration change, and start logs. Independent logs allow user to see last fault even if it occurred years ago
- Fault log tracks 150 faults with date and time stamp accurate down to the second:
- Allows users to diagnose power problems and prove them to your power provider
- Unit will give users a ‘snapshot’ of conditions at the time of fault, such as line to line voltage and current, alarms present, and I/0 status
- Format of time stamping example: 7/7/16 10:15:24
Application-based Setup
- SubMonitor Connect is an advanced, comprehensive, 3 phase motor protection relay that allows users to dial in protection and automation with extreme accuracy and parameter depth. However, SubMonitor Connect also has a streamlined Basic Setup Wizard to allows user to get up and running quickly
- 9 simple steps to program unit
- Users select between Submersible, Surface, or Custom and SubMonitor prepopulates protection parameters accordingly
- Confirm basic motor info, key protection info, time to get started
Automation Ready - Advanced Pump Control
- 12-240 VAC/VDC wet input for remote start/stop
- Dry contacts for auto run/shutdown or high float/low float
- Modbus RTU communication
- Automatic fault reset and on and off delay settings
- Automatic fault reset and on and off delay settings
Heavy-duy Industrial-grade Construction
- Outdoor rated, gasketed, powder coated, NEMA 3R enclosure designed in house by Franklin Electric to optimize layout and functionality
- UL 489 circuit breaker disconnect for branch and short circuit protection
- No fuses required saving time and money
- Lockable handle
Related
-
NEMA 3R, SubMonitor Connect Starter (With Service Entrance Circuit Breaker Disconnect)
Part Number 3-Phase Max. Amps / HP 200 V 230 V 460 V 600 V A HP** A HP** A HP** A HP** SMS3B-3A015S1 8 2 8 2 8 5 8 5 SMS3B-3A020S1 11 3 11 3 11 7.5 11 10 SMS3C-3A030S1 17 3 17 5 17 10 17 15 SMS3D-3A040S1 22 5 22 7.5 22 15 22 20 SMS3E-3A050S1 28 7.5 28 10 28 20 28 25 SMS3E-3A060S1 34 10 34 10 34 25 32 30 SMS3F-3A080S1 45 10 45 15 45 30 45 40 SMS3F-3A100S1 57 15 57 20 52 40 52 50 SMS3G-3A100S1 57 15 57 20 57 40 57 50 SMS3G-3A125S1 71 20 71 25 71 50 71 60 SMS3H-3A150S1 85 25 85 30 85 60 77 75 SMS3I-3A200S1 114 30 114 40 114 75 99 100 SMS3I-3A250S1 120 40 130 50 124 100 - - SMS3K-3A300S1 171 50 171 60 171 125 - - SMS3K-3A400S1 228 75 228 75 228 150 - - SMS3L-3A500S1 285 100 285 100 285 200 - - SMS3L-3A600S1 342 100 342 125 342 250 - - SMS3L-3A800S1 359 125 360 150 361 300 - - - 3 Phase, 50/60Hz, 200~600VAC, NEMA Type 3R Enclosed Starter
- *Standard Models not available in 1-Phase
- **HP rating is based on standard NEMA B, 4-pole motor design as represented in NEC table 430.150 full-load current, 3-phase alternating current motors.
SubMonitor Connect
Description Part No. SubMonitor Connect - Standard, 1-135A 5860015010 SubMonitor Connect - Premium, 1-135A* 5860005110 Factory Installable Options
Part Number Description SMS-SRG-240V Surge Supressor 240VAC SMS-SRG-480V Surge Supressor 480VAC SMS-SRG-600V Surge Supressor 600VAC SMS-STSP Start/Stop Pushbutton Control (in lieu of HOA switch) SMS-HOA-START Start Pushbutton when HOA in hand SMS-RPL Run Pilot Light SMS-FPL Fault Pilot Light SMS-DR-DISPLAY Door Mounted Keypad SMS-1PH Wiring for Single Phase Input SMS-CAM-KEY Keyed Enclosure Latch SMS-CAM-PAD Padlockable Enclosure Latch SMS-HOA-KEY Keyed HOA Switch - Factory Installable Options apply to configured-to-order models only and are subject to variable lead times. Consult your Franklin Electric Representative.
SubMonitor Starter Starter Type Dimensions Mounting H W D Hardware Size Spacing (Height x Width) SMS3B-3A015S1 with Service Entrance
Circuit Breaker Disconnect22 15 10 5/16" 17 & 5/8 x 12 & 3/4 SMS3B-3A020S1 SMS3C-3A030S1 SMS3D-3A040S1 SMS3E-3A050S1 SMS3E-3A060S1 SMS3F-3A080S1 SMS3F-3A100S1 SMS3G-3A100S1 SMS3G-3A125S1 SMS3H-3A150S1 SMS3I-3A200S1 32 15 10 5/16" 27 & 5/8 x 12 & 3/4 SMS3I-3A250S1 SMS3K-3A300S1 42 25 15 3/8" 20 & 7/8 x 37 & 3/4 SMS3K-3A400S1 SMS3L-3A500S1 62 25 15 3/8" 30 & 7/8 x 37 & 3/4 SMS3L-3A600S1 SMS3L-3A800S1 - *All measurements shown in inches.
-
Starter Type Full Voltage, Non-Reversing with Service Entrance Rated Circuit Breaker Disconnect NEMA Type 3R Enclosed - Rain Tight User Interface Control Hand-Off-Auto Switch Setting Adjustments SubMonitor keypad, 32 character, backlit NEMA 4X display
FE Connect Mobile App (Bluetooth)Environmental Ambient Operating Temp -5 °F to 140 °F (-20 °C to 60 °C) Ambient Storage Temp -5 °F to 185 °F (-20 °C to 85 °C) Relative Humidity 5% to 95% non-condensing Inputs/Outputs Inputs Voltage Auto-Run Applying 12-250VAC/DC will send a run command to the starter when in Auto Mode. Dry Contract Auto-Run / Low Float Normally Open or Normally Closed, adjustable, Default = Normally Open
Closing the circuit between the D1 & D terminals will send a run command to the starter when in Auto Mode.
Can be used with Shutdown/High Float terminal to set up float switch drain or fill operation.Dry Contact Shutdown / High Float Normally Open or Normally Closed, adjustable, Default = Normally Closed
Opening the circuit between the D2 & D terminals will shut down the starter.
Can be used with Shutdown/High Float terminal to set up float switch drain or fill operation.RS-485 Modbus RTU & BACnet MSTP Communication PT100/1000 PT100/1000 input, On/Off, adjustable, 0-100oC Output Fault Relay Output Normally Open Relay - Rated for 12-240V, closes in a fault condition Overload Operational Specifications Overload Type Electronic I2T trip curve Overload Trip Class Adjustable: 5-30, Default = 10 Overload Setting Range Differs per model Overload Service Factor Adjustable: 1.00-2.00, Default = 1.15 Under Power (Dry Run) On/Off/Alarm, adjustable, 1-99% of kW setting, Default = On/65% Over Power On/Off/Alarm, adjustable, 101-200% of kW setting, Default = On/125% Under Voltage On/Off/Alarm, adjustable, 80-99% of voltage setting, Default = On/90% Over Voltage On/Off/Alarm, adjustable, 101-125% of voltage setting, Default = On/110% Voltage Phase Loss Always on Ground Fault (UL 1053 Certified) On/Off/Alarm, adjustable, 1-10A, Default = On/1A Cycle Fault On/Off, adjustable start limit, 2-100, default = On Warm Start Provision On/Off, delays motor restart based on calculated motor temperature, Default = On Current Phase Unbalance On/Off, adjustable, 1-50%, Default = On/5% Locked Rotor/Stall On/Off, trips if current exceeds 300% of FLA/SFA setting for 0.5 seconds, Default = On Out of Calibration On/Off, trips after 10 seconds if the calculated FLA/SFA setting is set too high, Default = Off Max Time to Start On/Off, regardless of max amps or I²T trip curve,
always trip at start if starting current is outside of an acceptable range and still decreasing after 10 seconds.
Default = OffPower Fail Modes Adjustable, return to last mode (Hand/Off/Auto) or return in Off mode On/Off Time Delay On/Off, adjustable, 1-60 seconds Backspin Delay On/Off, adjustable, 2 seconds - 60 minutes Fault Reset Manual/Automatic, adjustable (default differs per motor protection feature) Agency Approvals UL/cUL, CSA -
